Kenmore appliance repair in Farmington, NM
Plenty of Kenmore washers, dryers and fridges from the Sears years still run in Four Corners homes, and many are worth keeping. We find the worn part, track down the right replacement and get the appliance working again.
- Answered 24/7
- Gas, electric and propane
- Farmington and the Four Corners
Kenmore jobs on our list
- Top-loader fills, then won't agitate or spin
- Dryer tumbles but never gets warm
- Freezer back wall caked with frost
Quick answer
On Kenmore appliances, the common repairs are washer lid switches, motor couplers and drive parts, dryer thermal fuses, belts, rollers and heating elements, refrigerator defrost and fan failures, and range elements and igniters. Many Kenmore models were made by other manufacturers, so the model number tells us the parts. Typical repairs around Farmington run about $118-$436, and most wrap up on the first visit. The phones are covered around the clock.
Brands we repair: Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Bosch, Kenmore, Electrolux, Amana, Speed Queen, Sub-Zero, Hotpoint
Why Kenmore repairs start with the model number
Kenmore was the Sears house brand for decades, and Farmington's ranch homes and manufactured homes still hold a lot of them: heavy top-load washers, matching electric and gas dryers, top-freezer and side-by-side refrigerators, chest freezers in the garage and plain, sturdy ranges. Many of these units have run for years with little attention, which says something about their simple designs. When one stops, the fix is usually a wear part, not the end of the appliance.
Here's the catch. Many Kenmore models were made by other manufacturers, so the model number tells us the parts. The digits before the dot on the Kenmore label point to the company that built that unit, and the rest identifies the exact model. Two Kenmore washers that look alike can take completely different lid switches or drive parts. With the full model number in hand, our tech orders the correct part the first time instead of guessing from the look of the cabinet.
Bought your Kenmore fairly recently? Dig out the paperwork that came with it, because the maker's warranty may still be in force, and a claim through that coverage could cost you less than a service visit. If it has run out, call us. We fix Kenmore appliances in Farmington, Bloomfield, Aztec, Shiprock and Kirtland, plus Durango, Cortez and the towns between, and the phone is answered around the clock when a freezer quits in the middle of the night.
Kenmore parts our techs replace most
These are the repairs we make most on Kenmore units, old and new.
Lid switch and motor coupler
On older direct-drive Kenmore top-loaders, the lid switch and the plastic motor coupler are common failures. We replace them, check the drive motor and confirm both agitate and spin work.
Agitator dogs and tub parts
If the top of the agitator spins freely by hand, the agitator dogs have worn smooth. We swap the dogs, check the tub seal and inspect the hoses while the washer is open.
Dryer fuse, element and thermostats
We test the thermal fuse, heating element, cycling thermostat and high-limit thermostat on electric dryers, and on gas models, the igniter, the flame sensor and the coils on the gas valve.
Dryer belt, rollers and idler
A dryer that thumps, squeals or won't tumble gets new drum rollers, an idler pulley, glides and a belt as needed, so it runs quietly for a good while longer.
Defrost heater, thermostat and timer
For refrigerators that frost up, we test the defrost heater, defrost thermostat and timer or control, then replace the failed part and clear the evaporator coil of ice.
Range elements, switches and igniters
We replace burned bake and broil elements, surface elements and their receptacles, infinite switches and gas oven igniters, then check that the oven holds its set temperature.
Kenmore trouble signs we hear about most
These are the Kenmore problems that fill our schedule, from Sears-era laundry to newer kitchen units.
Washer fills but won't agitate
On many older Kenmore top-loaders, a broken motor coupler, worn agitator dogs or a failed lid switch stops agitation or spin. The motor may hum while the tub sits perfectly still.
Washer leaks during the cycle
Water under an older Kenmore washer usually comes from a cracked fill hose, a worn tub seal, a loose pump hose clamp or a split water pump. Where the puddle forms tells us which.
Dryer turns but stays cold
Electric Kenmore dryers lose heat when the thermal fuse blows, the heating element opens up or the cycling thermostat sticks. On gas models, the igniter or gas valve coils are the usual suspects.
Dryer thumps or squeaks
A rhythmic thump points to flat-spotted drum rollers, and a high squeal to an idler pulley gone dry or glides worn thin. A snapped belt leaves the motor running while the drum sits idle.
Refrigerator warm, freezer frosted
Heavy frost on the back wall of the freezer plus a warm fresh food section means the defrost system failed: the heater, the defrost thermostat, or the timer on many older units.
Range element or burner out
A bake element that blistered or a surface burner that won't heat usually needs a new element, receptacle or infinite switch. On gas ranges, a weak oven igniter keeps the gas valve closed.
What Kenmore repairs usually run near Farmington
Most Kenmore repairs in the area land inside these ranges. None of it is a quote, because the model, the maker behind it and the part decide the total.
| Washer lid switch or motor coupler | $118-$227 |
|---|---|
| Washer drive parts, pump or tub seal | $176-$436 |
| Dryer thermal fuse, element or thermostat | $127-$268 |
| Dryer roller, idler and belt kit | $158-$297 |
| Refrigerator defrost or fan repair | $168-$384 |
Parts for some older Kenmore models are discontinued, and a compatible replacement can take a few extra days to arrive, which affects timing more than price. A new compressor or any sealed-system repair costs more than the figures above.
How Four Corners homes wear down Kenmore appliances
A lot of Farmington homes date from the 1950s to 1970s boom years, and many have Kenmore laundry sitting in a utility room or carport that was set up decades ago. Those spaces often come with long dryer vent runs and old shut-off valves. A long vent full of dust overheats a Kenmore dryer and pops its thermal fuse, so swapping the fuse alone won't hold. We check the vent run before closing the dryer back up.
Hard water hits older Kenmore machines in quiet ways. Minerals narrow the inlet screens on washers so fills slow down, and scale crusts the refrigerator water valve and ice maker on side-by-side models. Spring wind leaves fine dust on the condenser coil under the fridge. A garage refrigerator or chest freezer working through a 90-degree July or a January night in the teens wears out its start relay and fans faster than one kept in the kitchen.
Kenmore gas dryers and ranges in homes outside city gas service often run on propane, and they need the correct LP orifices and regulator setting. At about 5,400 feet, burners should match the high-altitude setup in the manual. A yellow, lifting flame or soot on the grate means the setup is off. If you smell gas, everybody heads outdoors first and calls the gas utility or 911 from out there, and we come in after the line is declared safe.
How a Kenmore repair visit unfolds
- Before the visit
Find the full model number
Look for the label under the washer lid, on the dryer door frame, inside the fridge wall or behind the range drawer. Read us every digit, including the part before the dot.
- On arrival
See the symptom
Our tech runs the appliance, listens and watches for the fault you described, and asks how old the unit is and whether it has been repaired before.
- Testing
Find the worn part
We open the cabinet, meter switches, fuses and heaters, and check drive parts by hand. You get the cause and the price before any part is installed.
- Same visit
Repair from the truck
Common Kenmore parts like lid switches, couplers, thermal fuses, belts and igniters often ride along with us. Hard-to-find parts get ordered that same day.
- Final check
Run it through
We run a full wash, a timed dry, a cooldown or a bake test, and tell you which other parts on an older unit look close to wearing out.
Is an old Kenmore worth fixing?
Often, yes. Older Kenmore laundry machines in particular were built with simple mechanical parts that are cheap to replace, and a washer that's 15 or 20 years old can keep going after a coupler or a lid switch. The questions are parts availability and the condition of the rest of the machine. If the tub bearing is failing, the cabinet is rusting through, or the part has been discontinued with no compatible replacement, we'll say so.
Refrigerators are a closer call. A defrost heater or fan motor is a sensible repair on an older Kenmore, but a compressor or sealed-system leak on a unit that age rarely pays off, especially since a newer refrigerator will also run on less power. You get the price and our honest read, then you decide.
Keeping an older Kenmore running longer
- Write the full Kenmore model number on a strip of tape inside a nearby cabinet door, since labels on older units fade and peel over time.
- Don't stuff an older top-loader with heavy comforters. Oversized loads wear out motor couplers, agitator dogs and transmissions much sooner.
- Have the whole dryer vent run cleared once a year, especially in a home where the duct snakes a long way to reach the outside wall.
- Vacuum the coil under or behind the refrigerator each spring and fall, since Four Corners dust settles there and keeps the compressor running longer.
- If a garage fridge or freezer struggles in July or January, move it into conditioned space if you can, or at least keep it out of direct sun.
Related repairs people book with kenmore appliance repair
Where we handle kenmore appliance repair
Farmington neighborhoods first, then the rest of San Juan County and southwest Colorado. Pick your area for local notes, or see all 41 locations.
Kenmore Appliance Repair questions from Farmington homeowners
Who actually made my Kenmore appliance?
Kenmore units came from several manufacturers over the years. The digits before the dot in the model number identify the builder, and the rest pins down the exact model. Read us the whole number when you call, and we'll match the parts to the right design.
Can you still get parts for an old Kenmore washer?
For many older Kenmore top-loaders, yes. Lid switches, couplers, agitator dogs, pumps and belts stay widely available because so many of those machines were sold. Some electronic boards and cosmetic parts are discontinued, and we tell you up front if a part can't be found.
What makes a Kenmore dryer burn through thermal fuses?
Overheating trips the fuse, and on most Kenmore dryers the heat builds up because the vent is clogged, crushed or simply too long. A failing cycling thermostat or a heating element shorting to the cabinet can do it too. We replace the fuse and find the cause so it doesn't blow again next month.
Is my Kenmore still covered by a manufacturer warranty?
Check the purchase date against the paperwork. A newer Kenmore might still sit under its original warranty, and filing that claim first can save the cost of a visit. If the coverage has expired, or the unit dates from the Sears years, call us and we'll diagnose it ourselves.
Why is my Kenmore refrigerator freezer full of frost?
A freezer with frost caked on the back wall usually has a defrost problem: a burned-out heater, a failed defrost thermostat, or a stuck timer or control. A door gasket that doesn't seal adds frost too. We test each one and replace the part that failed.
Do you repair Kenmore gas ranges that run on propane?
Yes. We work on Kenmore gas ranges running natural gas or LP, replacing oven igniters, surface burner parts and valves, and checking that the orifices and regulator match the fuel. A flame that burns yellow or lifts off the burner tells us the setup needs attention.
Need kenmore appliance repair today?
Call any hour. A real person picks up, takes the model number and sets the visit.